Frac pump Trailer
The GOES Pumper F-PU-Tr is a trailer mounted, single pump unit with a high performance engine, transmission and high pressure positive displacement Quintuplex pump.
The Unit can be remotely operated either from a remote control module or from the data van through a Mobile Computerized Data Acquisition and Control Unit.
Axle load of loaded (ready for operation) Unit does not exceed 8 tons per axle. The load to the fifth wheel of tractor is no more than 8 tons.
The unit described in this specification is designed and built for severe environmental conditions ranging from -40°C to + 40°C.
Year of Manufacture : / Working Hours : ~ 1000h
- Engine Type: MTU 12V4000S83
- Transmission Type: Allison
- QWS 2500
Dimensions
Length: 11450 mm / Width: 2550 mm / Height: 4000 mm / Weight: 30050 kg
- Various Units available in Europe
Frac Pumping Unit 2250 BHP
Year of Manufacture : 2012 / Working Hours : – Depends on Pump. 10 Frac Pump trailers available.
Enghine Hrs : Between 240h – 420h
Pump Hrs : Between 100h – 175h
- Tandem (two) Axle fixed gooseneck, “single drop” Trailer
- Diesel Engine: MTU 12V 4000 S83, rated 1680kW @ 1900 RP;
- Transmission Type: Allison S9820A
- High Pressure Pump TWS 2250 Triplex. 4.5″ Plunger
Dimensions
Length: 12500 mm / Width: 2550 mm / Height: 4000 mm / Weight: 28500 kg
- 10 Units available in Europe
Frac Blender
Tri Axle Trailer Mounted Frac Blender, built by Surefire.
Dimensions : 102”W x 553”L x 155” H
Year of Manufacture : / Working Hours : 13000 h
- Engine – Dual Cummins 665HP, QSX15 Tier II
- Three (3) Augers
- Open Tub
- One Unit available in USA
Frac Sand King
Trailer Mounted Frac Sand King, built by Cambelt.
Dimensions : 96”W x 645”L x 158” H
Year of Manufacture : / Working Hours : 6000/8000 h
- Cummins Generator
- 2 Units available in USA
Acid Frac Tanks
This carbon steel tank trailer is designed to store acid, water for frac sites or groundwater remediation projects. It is easy to move, clean and suitable to store 83 m³ of liquid.
Year of Manufacture : 2016 / Working hours : 0 h
According E.E.C Rules
Dimensions
83m³ Capacity
- 2 Units available in Europe
Data Van Trailer Mounted
This Data Van Container Trailer Mounted provides operation of Fracturing Fleet with 7 Pumping Units, Blender, Chemical van and Hydration Unit.
Year of Manufacture : 2019 / Working Hours :
- Trailer
- Van Container
- Generator
- 2 Industrial dual PC
- 3 Touch monitors 27”
- 1 Touch monitor 24”
- GOES/Prime DMS/DAS
- Unit connection boxes with cable reels
- UPS System
- Outdoor LED spot lights
- Complete interior like Benches, Fridge, Coffee Machine
- One Unit available in Europe
Single Pump Trailer
Year of Manufacture : / Working Hours : 2650 h
- Engine type: CAT-C18
- Transmission: EATON Manual
- Gardner Denver Triplex HP Pump
- One Unit available in Europe
Single Pump Container
Compact Design for High Pressure Pumping
The 500hp Pump unit is mounted inside the 20’ container and designed for operations in rough oilfield environments. Each component of the pump unit is selected to provide optimum performance, considering operating conditions and serviceability, which is available for rental now.
- For high pressure pumping or fluid circulation
- Support different type of well service interventions
- Used for high-pressure liquid carbon dioxide pumping,
acidizing, cementing operations, pressure testing, etc. - Engine pre-heaters for extreme weather conditions
- Remote control
- CE conformity
Dimensions
Length: 6.100 mm / Width: 2.460 mm / Height: 2.700 mm / Total Weight: 13.000 kg
Components
- Diesel Engine
- High Pressure Triplex Pump
- Transmission
- Various Units available in Europe
GOES SP600-30 Single Pump Skid
This Skid Mounted Single Pumping Unit is capable of pumping well servicing fluids into oil and gas wells that is suitable for onshore/offshore operations and is capable of operating in a ambient temperature range of 0 Deg C to +55 Deg C.
The Unit configuration will include the following features:
– This Unit to be controlled locally from a Unit Mounted Digital Control System
– The Unit Power Package is centrally mounted at the front of the Skid with the drivelines directed toward the rear of the Unit.
– The Triplex Pump is direct driven from the Power Package and be mounted at the rear of the Unit.
– The High and Low Pressure Manifolds and Piping is integrated within the Unit for accessibility and minimal flow restrictions. Piping will discharge at the rear of the Unit.
Year of Manufacture : 2020 / Working Hours : 0 h
- Carrier 1 Heavy duty skid/lift frame
- Diesel Engine 1 CAT C15 ACERT rated a minimum of 595 BHP @ 2100 RPM
- Transmission 1 Allison 4700 OFS Transmission
- Cooling System 1 Vertical radiator with Mechanical Fan Drive
- Hydraulic System 1 Open Loop
- Triplex Pump 1 GD 600 Compact Triplex
- High Pressure Piping 1 2” Fig 1502, 15,000 PSI (103 mPa)
- Low Pressure Piping 1 150 PSI (1.03 mPa)
- Boost Pump 1 Mission Magnum Type 4” x 3” x 13” Centrifugal
- Controls System 1 Control Console, Local Controls and Data Acquisition
- One Unit available in KSA
Twin Pump Skid
This “Serviced/Tested” Skid Mounted Twin Pumping Unit is suitable for onshore/offshore operations.
Year of Manufacture : 1986 / Working Hours : 200 h
- Carrier – Heavy Duty Skid / protection frame
- Cabin – Two Rooms, Isulated
- Deck Engines – 2 DDC 12V71
- Deck Transmissions – 2 Allison CLT 6061
- Cooling Systems – Vertical radiator with Mechanical Fan Drive HES HT400
- High Pressure pumps : 2 HES HT400
- Control Systems – Control Console with Local Controls, GOES DAS
- One Unit available in Europe
Trailer Mounted Twin Pump Unit
This Trailer Mounted Twin Pumping Unit is capable of holding, mixing and pumping INHIBITED acids and other well servicing fluids into oil and gas wells. This Unit is suitable for towing via a fifth wheel attachment by CUSTOMER supplied Truck Tractor.
Year of Manufacture : 2020 / Working Hours : 0 h
- A Control Cabin mounted towards the rear of the Trailer in between the Displacement Tanks and the High Pressure Pumps
- An Operators Platform allow access to the Control Cabin and the Displacement Tank.
- Displacement Tank mounted directly behind the Control Cabin to facilitate operator access and line of sight from controls.
- The two Unit Power Packages are mounted in a side by side configuration at the front of the Trailer lower deck with the drivelines toward the rear of the Unit.
- The High Pressure Pumps are direct driven from the Power Packages and be mounted at the rear of the Unit.
- The High and Low Pressure Manifolds and Piping are integrated within the Unit for accessibility and minimal flow restrictions. Piping discharge at the rear of the Trailer.
- Good access to solenoid valves and filters and dipsticks
- Drain ports and loading aperture for oil to outside (good access)
Carrier 1 Tandem (2) Axle fixed gooseneck, “single drop”trailer
- Diesel Engines 2 CAT C15 ACERT rated a maximum of 595 BHP @2100 RPM
- Transmissions 2 Allison 4700 OFS
- Cooling Systems 2 Vertical radiator with Mechanical Fan Drive
- High Pressure Pumps 2 SPM TWS 600S HD (Compact Version)
- High Pressure Piping 1 2” Fig 1502, 15,000 PSI (103 mPa)
- Low Pressure Piping 1 150 PSI (1.03 mPa)
- Displacement Tank 1 20 BBL (3.2 m3) Total Capacity, 2 Compartments
- Boost/Fill Pumps 2 GD 6” x 5” x 11” Centrifugal
- Controls System 1 Control Cabin with Control Console for Local Controls and GOES Data Acquisition
- One Unit available in Europe
Twin Cementing Truck Unit
Built by Peterbilt
Year of Manufacture : 1998 / Working Hours : 7700 h
- Caterpillar Engine
- Allison Transmission
- Two Gardener Denver HP Pumps
- Displacement Tanks
- Mark 3 Cement Mixing Head
- Operator Stand
- One Unit available in Europe
Wireline Logging Unit
Year of Manufacture : 2017 / Working Hours :
- Mercedes Actros 3341 6×6
- Two Compartment Cabin Layout
- Benchmark Measuring System
- Tool Racks
- Suitable for -40 C° – +55 C° Environment
- Winch System Suitable for 7/32“ – 17/32“ cable
- One Unit available in Europe
Multi Purpose Pumping Unit
3.5 million BTU in-line heater and 10.000 psi triplex pump
The 500 HHP Multi Purpose Pumping Unit “MPPU” is available for rental to heat and pump various fluids, suitable for mix and squeeze acid systems, gravel-packs, consolidation, dewaxing and tensioactive treatments.
- Pump rate: 20-600 l/min
- Heating oil, condensate or water on the fly and reduce treating time and cost drastically
- Stainless steel construction and 12 speed pump operation allows all types of acid jobs
- Magnetic flowmeters and modern data acquisition
- Paraffin dispersant in wellbores and pipelines
- All type of Well stimulations
- Well treatments with all types of solvents
- Pump and circulation operations
- Filtration system installed
- CE certified
Main Components
- Triplex pump: SPM TWS 600
- Transfer case: NAMCO 2 speed
- Centrifugal pump: Mission 6“x 5“
- Loading pump: Roper 3“
- Heater: 3.5 million BTU
- Data acquisition: included
- Tanks: 2 x 3 m³ stainless steel
Carrier Vehicle
- Volvo FMX 500 6×4
- Engine power (V6) : 500 PS
- Maximum technical axle load: 9/9/13 t
Dimensions
Length: 11.5 m / Width: 2.5 m / Height: 3.9 m / Total Weight: 22.0 ton
Various Units available in Europe.
Trailer Mounted 180K N2 Pump Unit
This Unit incorporates a Nitrogen Pumping System capable of pumping high pressure gas at rates of up to 180,000 SCFH/85m3/min and at pressures of up to 10,000 PSI/69 mPa. This Nitrogen Pumping System connects to a single 3,000 gallon (11.36 M3) liquid nitrogen tank that will be installed at the rear of the Trailer.
The nitrogen side of the Unit is powered by a CAT C15 Diesel Engine rated at a maximum of 540 @ 2100 RPM. The Unit is equipped with a cryogenic centrifugal boost pump, cryogenic high pressure Triplex Pump, non-fired vaporizer system and other components.
All of the hydraulically driven components are powered from the Unit mounted Diesel Engine. During normal operation, liquid nitrogen flows from the cryogenic liquid nitrogen storage tank through the centrifugal boost pump (where suction pressure is boosted) to the Triplex Pump, where it is pressurized by reciprocating pistons to downstream pressure.
The high pressure liquid then flows through the non-fired nitrogen vaporizer system absorbing a sufficient amount of heat to raise the gaseous nitrogen discharge temperature to 15 to 21 Deg C (60 to 70 Deg F) and flows out to a discharge valve as high pressure gas at rates of up to 180,000 SCFH/85m3/min and at pressures of up to 10,000 PSI/69 mPa. This Unit may be controlled locally from the Control Console installed in a Unit mounted Control Cabin.
Year of Manufacture : 2020 / Working hours : 0 h
- Carrier 1 Tandem (2) Axle fixed gooseneck, “single drop” trailer
- Diesel Engine 1 CAT C15 ACERT 540 BHP @ 2100 RPM
- Cooling System 1 Vertical radiator with Mechanical Fan Drive
- Power Transmission 1 Multi-output drive gearbox,
- Hydraulic Drive System 1 Closed and open loop hydraulic systems
- Triplex Pump 1 ACD 3-GUPD (or equivalent) Cryogenic Type Pump
- LN2 Boost Pump 1 ACD18 (or equivalent) 1 ½” x 2 1/2” x 6” hydraulically driven centrifugal pump
- LN2 Vaporization System 1 Non fired (heat recovery) type with Hydraulic Pump make-up Diesel Engine loading system and Water Bath type Vaporizer
- Auxiliary Coolant Pump 1 Centrifugal type pump
- Low Pressure Piping 1 Stainless steel
- High Pressure Piping 1 103 mPa (15,000 PSI) stainless steel/2” Fig 1502
- Nitrogen Tank 1 3,000 gallon (11.36 M3) liquid nitrogen tank
- Controls System and Instrumentation 1 Control Cabin with Control Console, Local Controls, Data Acquisition
- One Unit available in Europe
180K N2 Trailer Mounted Pump Unit
Modular Skid Design on Trailer
Year of Manufacture : / Working Hours : 2650 h
- Detroit Diesel Engine
- Triplex Pump
- LN2 Boost Pump
- LN2 Vaporization System
- 2000 GAL Nitrogen Tank
- One Unit available in Europe
N2 Pump Unit – Trailer Mounted
This fully assembled Unit incorporates a Nitrogen Pumping System capable of pumping high pressure gas at rates of up to 180,000 SCFH/85m3/min and at pressures of up to 10,000 PSI/69 mPa and at a gaseous nitrogen discharge temperature range of 15 to 21 Deg C (60 to 70 Deg F).
Year of Manufacture : 2020 / Working Hours : 0 h
- Carrier 1 Tandem (3) Axle fixed gooseneck, “single drop” trailer
- Diesel Engine 1 CAT C13 ACERT rated a minimum of 475 BHP @ 2100 RPM
- Cooling System 1 Vertical radiator with Mechanical Fan Drive
- Power Transmission 1 Multi-output drive gearbox,
- Hydraulic Drive System 1 Closed and open loop hydraulic systems
- Triplex Pump 1 ACD 3-GUPD (or equivalent) Cryogenic Type Pump
- LN2 Boost Pump 1 ACD18 (or equivalent) 1 ½” x 2 1/2” x 6” hydraulically driven centrifugal pump
- LN2 Vaporization System 1 Non fired (heat recovery) type with Hydraulic Pump make-up Diesel Engine loading system and Water Bath type Vaporizer
- Auxiliary Coolant Pump 1 Centrifugal type pump
- Low Pressure Piping 1 Stainless steel
- High Pressure Piping 1 103 mPa (15,000 PSI) stainless steel/2” Fig 1502
- Nitrogen Tank 1 3,000 gallon (11.36 M3) liquid nitrogen tank
- Controls System and Instrumentation 1 Control Cabin, Local Control
- One Unit available in Europe
2.000 Gallons Nitrogen Storage Tanks
The skid mounted Nitrogen tank is Cryogenic Offshore Vessel, suitable for storage Nitrogen for easy operation and safety transportation.
Year of Manufacure : 1988 – 2006
- Inner vessel material: 304/304L stainless steel
- Outer vessel material: ST52
- Super insulation
- NER (Normal Evaporation Rate): 0.60 N2% / day maximum
- Third party certification available
- DNV certified
Dimensions
Length: 3.645 mm / Width: 2.435 mm / Height: 2.590 mm / Total Weight: 29.050 kg
Components
- Capacity: 8.4 m3
- Maximum Working Pressure: 3.1 bar
- Design pressure: 5.33 bar
- Design Temperature Inner Vessel: -196 °C
- Design Temperature Outer Vessel: +50 °C
- Design Ref. DNV 2.7-1 / EN 13458
4 Units available in Europe
4.000 Gallons Nitrogen Storage Tanks
The skid mounted Nitrogen tank is Cryogenic Offshore Vessel, suitable for storage Nitrogen for easy operation and safety transportation.
Year of Manufacure : 2007
- Inner vessel material: 304/304L stainless steel
- Outer vessel material: ST52
- Super insulation
- NER (Normal Evaporation Rate): 0.60 N2% / day maximum
- Third party certification available
- DNV certified
Dimensions
Length: 6.058 mm / Width: 2.435 mm / Height: 2.590 mm / Total Weight: 29.050 kg
Components
- Capacity: 16.7 m3
- Maximum Working Pressure: 3.1 bar
- Design pressure: 5.33 bar
- Design Temperature Inner Vessel: -196 °C
- Design Temperature Outer Vessel: +50 °C
- Design Ref. DNV 2.7-1 / EN 13458
- One Unit available in Europe
Generator Container
The skid mounted Nitrogen tank is Cryogenic Offshore Vessel, suitable for storage Nitrogen for easy operation and safety transportation.
Year of Manufacure : 2014
Dimensions
Length: 6.058 mm / Width: 2.438 mm / Height: 2.591 mm / Total Weight: 7.000 kg
Components
- Electric Generator 200kW
- Diesel Engine Deutz
- Air Compressor max 7.5 bar
- Electric Panel Output voltage frequency : 400/50 Hz
- Air Reservoir : 300 l
- One Unit available in Europe
Batch Mixer
2 x 10m³ Premix Tank
The 20 m³ Batch Mixer is available for rental/Sales in good conditions and with economical price, which is heavy-duty skid mounted for easy transportation and efficient cementing job
- Electrically driven
- Mixing Paddles inside mixing tanks
- Charge pump: Mission
- All connections: WECO
- Circulation manifold included
- Tank: 2 x 10m²
- Bulk cement line: 3″
- Sunction line: 4″
- High Pressure line: 2″ 1502
- One Unit available in Europe
BOP, 4-116” 10K Quad
Used to provide positive protection against blow-outs and to secure the well in an emergency. This allows work to be safely carried out, under pressure, on surface equipment while the tubing is still in the wellbore.
The BOP closing design consists of a hydraulic actuator assembly connected to each ram assembly. This allows the rams to be hydraulically compressed around the tubing from opposite sides which creates a seal, thus containing well pressure below the rams.
Pressure across the rams is equalized, through an equalizing assembly located across each ram assembly. This takes place prior to hydraulic retraction of the rams.
Year of Manufacture : 2020 / Working Hours : 0 h
- c/w bridal hoses **HAND WHEEL MODS NE-080-A188**
- 4.06″ inner diameter
- Ram Configuration:
- Blind / Shear Rams
- Slip Rams
- Pipe Rams
- Pipe Rams
- Includes 4-1/16″ 10K BX-155 studded flange up
- Includes 4-1/16″ 10K BX-155 studded flange down
- Includes 2-1/16″ 10K BX-152 Studded Flanged Side outlet with 2″ 1502 Weco Flange Adapter
- Hydraulic Retract System for Ram Service
- External hydraulics (actuator bridal hoses required)
- Includes Equalizing Valves
- Includes Teflon Coating inside BOP Body
- 10,000 psi W.P. / 15,000 psi T.P.
- H2S Service
- Coil Size: 1.75″
- Hydraulic Couplers: Plugged
- Paint: Paint Nexus Blue
- One Unit available in Europe
BOP, 3-116” 10K Quad
Used to provide positive protection against blow-outs and to secure the well in an emergency. This allows work to be safely carried out, under pressure, on surface equipment while the tubing is still in the wellbore.
The BOP closing design consists of a hydraulic actuator assembly connected to each ram assembly. This allows the rams to be hydraulically compressed around the tubing from opposite sides which creates a seal, thus containing well pressure below the rams.
Pressure across the rams is equalized, through an equalizing assembly located across each ram assembly. This takes place prior to hydraulic retraction of the rams.
Year of Manufacture : 2020 / Working Hours : 0 h
- 3.0625″ inner diameter
- Dressed For 1.50″ Coiled Tubing Size
- Includes 3-1/16″ 10K BX-154 Studded top open flange bottom
- Includes 2-1/16″ 10K BX-152 Studded Flanged Side Outlet with 1502 Weco Flange Adapter
- 2-1/16″ BX-152 10-K Side Port Is Positioned Between 2nd & 3rd Rams
- Ram Configuration:
- Blind Ram
- Shear Ram
- Slip Ram (1.50″)
- Pipe Ram (1.50″)
- Shear Ram Actuator is Larger then other actuators, no booster required
- Includes Equalizing Valves
- Includes 4:1 De-booster Assembly
- c/w Actuator Ram Position Indicator Windows and Manual Hand Wheel Locks
- Includes Teflon Coating inside BOP Body
- 10,000 psi W.P. / 15,000 psi T.P.
- H2S Service
- Paint: Ultra Green Primer
- Coil: 1.5″
- Hydraulic Couplers: Plugged
- Includes BOP stand (NE-080-A45)
- One Unit available in Europe
Drilling Rig Futura -1/ Drillmec HH-75 Trailer Mounted
Year of Manufacture : 2007 / Working Hours :
- Hydraulic Drilling Rig – Drillmec HH75, S/N 11817
- Trailer
- 2 ea. CAT GmbH Pump Container TWS 600
- Generator 450kVA (RD8101)
- Mud Tank 61 m3, 3 ea. Shale Shakers w/ 2 ea. Agitators
- Mud Tank 63 m3, 1 ea. Hoper w/ 2 ea. Mission Pumps
- 13 5/8” x 3000 Double Rams Preventer, 1ea. Drilling Spool
- 13 5/8” x 3000 Hydrill Annular Preventer
- Shaffer BOP Accumulator Unit 3,000 psi
- Choke Manifold 3 1/8” x 3000, 2 ea. 3 1/8” Choke valves
- Fuel Tank, 9,000lChoke Manifold (Meet API requirements)
- One Unit available in Europe
Wellhead Isolation Tool (Treesaver)
This specification covers a Wellhead Isolation Tool suitable for Gas/Oil Acid Fracturing operations. This Unit will be supplied loose suitable for storage/transportation by a suitable customer supplied Truck Chassis or Trailer.
The equipment will be capable of operating in an ambient temperature range of 0 Deg C to +55 Deg C. (32 Deg F to +131 Deg F). The proposed Unit will include the following main components:
A/ Hydraulic Power Unit
This is not included but can be supplied. The intention is the customer will supply hydraulic power with the crane truck that will deliver the unit the well site.
B/ Treesaver Assembly
This is a “Low Profile” design Unit (valve is only 14” (36 cm) above the wellhead), that utilizes two hydraulic cylinders (with integral bleed off valves) and is direct flange connected to the wellhead (customer to advise required flange specifications). This Treesaver may be installed while wells are under pressures of up to 5,000 PSI (34.5 mPa).
C/ High Pressure Tube Assembly
The High Pressure Tube Assembly consists of:
- Mandrel (By-pass tube)
- Mandrel Extensions
- Pack-Off Nipple
- Bull Nose
- One Unit available in Europe
GN Tree Saver 2 78″ and 3 12″
Well Stimulation treatments are often characterized by high pressure (higher than the wellhead ratings), large volumes of strong acid, large amounts of sand, or some combinations of these. The GN Tree Saver allows operators to protect their wellhead from these high pressures and from corrosive or abrasive fruids, saving unnecessary Christmass Tree/Wellhead expenses.
The Tree Saver accomplishes this by insertign a high pressure mandrel into the wellhead above the flow cross and through all of the wellhead valves and fittings. The lower end of this mandrel seals into the well tubing/casing to isolate the Lellhead from the path of treating fluids.
Size: 2 7/8″ and 3 1/2″
Hydraulic Cylinders Stroke of 92.75″
Insertion Pressure up to 5.000 psi
Flow rate 26-35 bpm
3″ 1502 Lockdown Hammer Union
3″ 1502F Connection for Valve Assembly
Changeover Flange Tees
- 3 1/16″ 15K psi x 2 9/16″ 10K psi x 2″ 1502F
- 3 1/16″ 15K psi x 3 1/16″ 10K psi x 2″ 1502F
Mandrels
- Size 2 7/8″ Bore : 1.50″ Length : 1,2,3,5 ft
- Size 3 1/2″ Bore : 1.75″ Length : 1,2,3,5 ft
Pack-off Nipples w/Bull Nose
- Size : 2 7/8″ Tubing/Casing Weight : 6.4/6.5 lb/ft
- Size : 3 1/2″ Tubing/Casing Weight : 9.2/9.3 and 10.2 lb/ft
5-1/2” 15K Ball Launcher
Size: 5 1/2″
ID: 5,000″
Ball sizes: 1,250″ – 4.750″
Pressure rating: 15 000,00 psi
Ball Launch Capacity: 6 pcs
Lower Flange Connection: 5-1/8″ 15M w/ BX-169
Crossover Flange: 5-1/8″ 15M w/ BX-169 (Up) x 3-1/16” 15М (Down) w/ BX 154
It Comes with :
1. Qty 6, 100ft air hose and associated fittings
2. Control Panel
3. Skid
4. Air Compressor (Diesel)
5. Nitrogen system (Tank)
6. Tool Box
